Excluding PDF versions, files above are HTML and good for viewing.  Please select the PDF link for printable copies.  The PDF files are larger than their counterpart HTML files and will take longer to view due to download times.

Comminutors Manufactured By
G.E.T. Industries Inc.
T (905) 451-9900 or (877) 213-7418 F (519) 927-3261
Home      Contact Us     Site Map

To view some files on this site you will require the Free Adobe Reader
Links:

View our Trademark registration

MODEL 7A-6 - SPECIFICATIONS

1.0 General Specifications
    There shall be furnished one (1) one only Grind Hog^TM Model 7A-6 Comminutor as manufactured by
    G.E.T. Industries Inc. with rotation in a counter-clockwise direction.

 1.1 Design Criteria
    The comminutor shall be designed to handle the flows indicated below, within the head loss noted.
    a)   hydraulic capacity 315 GPM (19.9 l/s)
    b)   satisfactory operation shall occur under conditions of zero flow
    c)   head loss at peak flow shall not exceed 10 inches (250)
    d)   design shall be such that the flow enters the size reduction and screening device horizontally and
          exists vertically downward to facilitate the flushing of solids

 1.2 Rotating Drum Screen
      a)   heavy-duty Cast Ductile Iron ASTM 536, grade 60-45-18

1.3 Cutting Elements
      a)   replaceable shear bars constructed of high-quality A2 tool-steel shall be attached to the rotating
            drum.  Each shear bar shall be machined from solid bar stock, surface ground to establish exact
            tolerance
      b)   stationary cutting bar shall be of high-quality 01 tool steel hardened to a minimum of 56 Rockwell C,
            and shall be reversible, allowing for four (4) sets of cutting edges prior to sharpening or replacement
      c)   all submerged fasteners shall be of stainless steel

1.4 Flanged Body
      a)   the body of the comminutor shall be of high quality cast iron and so designed to allow free
            unobstructed flow of influent through the unit.  A Neoprene “O” Ring shall seal the chamber, allowing
            for operation under conditions of abnormally high head
      b)   the inlet flange shall be 6" (150)

1.5 Motor
    TEFC 1 Hp. Motor suited to outdoor weatherproof service (IP55) on _____ volt, ____ phase, ____ cycle
    service. Close-coupled

 1.6 Drive Arrangement
      a)   the motor shall be close-coupled to a speed reducer drive, a heavy duty planetary gear of the totally
            enclosed non-vented type suitable for total submergence during emergencies
      b)   double seals on the output shaft shall ensure flood-proof operation through a reduction ratio of 35:1
      c)   the cycloidal reducer shall be capable of withstanding shock loads to 500% of its mechanical rating
            of 1.61 Hp. and be warranted for two (2) years
      d)   the drive shall have a minimum full load efficiency of 90% and be pre-lubricated with grease,
            requiring routing maintenance every 500 to 1,000 hours

A) Auto-Coupling Slide Rail -  Wet Well
      a)   each Grind Hog^TM shall be equipped with a Slide Rail System allowing for removal without entering
            the wet well
      b)   a stationary PVC Overflow Coupling Box Assembly shall be flange mounted to the gravity sewer pipe
            as shown on the drawings.  An open top will allow for overflow in the event of a disruption in service
      c)   Guide Rails shall be of 304 stainless steel pipe, 1.5" in diameter, and shall be of adequate length as
            shown on the drawings
      d)   Guide Rail Supports shall be 304 stainless steel and shall be mounted to the wet well wall
      e)   all anchorage hardware shall be of stainless steel and shall be supplied by the contractor

B) Auto-Coupling Slide Rail - Chamber
      a)   each Grind Hog^TM shall be equipped with a Slide Rail System allowing for removal without entering
            the wet well
      b)   a stationary galvanized steel Overflow Bar Screen and influent trough shall be mounted under the
            gravity sewer pipe as shown on the drawing.  Support brackets and hardware shall be provided (304
            S.S.).  Anchorage shall be supplied by the contractor
      c)   Guide Rail Supports shall be of 304 stainless steel pipe, 1.5" diameter, and shall be of adequate
            length as shown on the drawings
      d)   Guide Rail Supports shall be 304 stainless steel and shall be mounted to the wet well wall
      e)   Mounting hardware shall be of stainless steel and shall be supplied by the contractor